Tape double joint valve

Settings

Per complete box pack In bag packs  
Ref. Diameter Box Units in box Bags in box Ref. Units in bag packs
1096 16 mm C 250 10 81096 25

CHARACTERISTICS: minimum load loss,
withstands up to 5 bar without any appreciable
water loss both when open or closed in normal
conditions.
MATERIAL/S: manufactured in reinforced
polypropylene. O ring seal in NBR.
APPLICATION: accessory used to connect
standard PE low pressure tubes for microirrigation
branch lines.
ASSEMBLY: introduce the tape until tip in the
conical end of the valve and turn left the screw
until fitting it. Do not damage the shape of
the tape.

You can REQUEST commercial or technical information about this product.

 

Related products

Diversion outlets

Materials:  manufactured in polypropylene.

Assembly: punch the main tube with a 7 mm. Punch part number 1171/1159 and insert the water inlet.

Application: in standard pe 32 tubes with a maximum permitted thickness of 4,8 mm.

Safety outlet

Materials: body in abs and ring in acetal resin.

Characteristics: the safety models are characterized by a mobile ring which increases in diameter if the tube shows signs of coming out of the accessory,  thereby immobilizing the tube and preventing it from working loose.  This system allows the accessory also to operate with thinner than standard tubes.

Assembly:  same as the previous types.

Safety outlet double joint for safety outlet

Los modelos de "seguridad" se caracterizan por tener un anillo movil el cual va aumentando su diametro conforme la tuberia intenta salirse del accesorio,  bloqueando el movimiento de la misma e impidiendo que se suelte.  Este sistema permite que el accesorio tambien funcione con tuberias de espesores inferiores a los normalizados.

double joint

MATERIAL/S: manufactured in a specially formulated material to provide flexibility and resistance to shearing, chemical agents and temperature changes.
APPLICATION: in PE tubes (with wall thickness values not exceeding 4 millimetres) and PVC tubes. The rigidity of the PE HD and PVC tubes makes it imperative to fit this flexible accessory to avoid leaks. It is not indispensable in the case of PE tubes (low density), but is recommended since it ensures perfect sealing and allows the best part of the water delivery section of the water outlets to be used. It is used in conjunction with water outlets for double joint part numbers 1133, 1145, 1105, 1056, 1058, 1041, 1042 and valves 1096 and 1097.
ASSEMBLY: punch a 17 millimetres opening in a tube. Remove roughness and burrs and insert the tapered part of the joint, then insert the water outlet.

XRT outlet

The xrt models have an improved design of the safety rings that, even looking so simple, hold the tube with the same fiability and less water looses than with the safety ring, allowing the installation of this accesory with less effort. This system allows too that the accesory works with pipes with less thickness to standardized.
 

Body in abs.

Installation and use and measures same than in the other outlets.

Patented design.

Stopper

Manufactured in polypropylene.

Assembly: accessory used to plug standard pe low pressure tubes for micro-irrigation branch lines.  HIS Type of accessory is inserted into the tube. The saw tooth pattern on the surface make easy to slide the tube up to the central stop, but prevents it from coming out. See also ring stopper.

Application in standard pe32 tube. 

XRT plug

The xrt models have an improved design of the safety rings that, even looking so simple, hold the tube with the same fiability and less water looses than with the safety ring, allowing the installation of this accesory with less effort. This system allows too that the accesory works with pipes with less thickness to standardized.
 

Body in abs.
 

Installation and use and measures same than in the other outlets.
 

Patented design.

Ring stopper

Manufactured in polypropylene.

Alternative  to the traditional stopper system  for plugging the ends of the irrigation tube, making the plugging/unplugging operation quicker and easier. 

Assembly: insert the tube into one of the opening, bend the end of the tube over and insert it into the other opening. 

Application in standard pe32 tube.

Dripper stopper 5x3mm

Manufactured in polypropylene.

Assembly:  insert the tapered part of the accessory into the tube.

Application: 
- measure 7 x 5: plug the holes made with the  3 mm punch, used to locate the drippers,,micro-sprinklers, micro-diffusers  and  threaded diffuser into the tube pe32 (maximum permitted thickness 2 mm.). Is also used as stopper for the microtube 6 x 4.

- measure 15 x 10: plug the holes made with the  7 mm punch,. Used to locate the outlets  (ref. 1051, 1103, 1104, 1141) on pe32 tube (maximum permitted thickness 4,8 mm.).

- measure 5 x 3: plug the 1 and  2 mm diameter holes in pe32 tube (maximum permitted thickness 2 mm).