Articles 25 - 36 total of 41

XRT plug

The xrt models have an improved design of the safety rings that, even looking so simple, hold the tube with the same fiability and less water looses than with the safety ring, allowing the installation of this accesory with less effort. This system allows too that the accesory works with pipes with less thickness to standardized.
 

Body in abs.
 

Installation and use and measures same than in the other outlets.
 

Patented design.

Ring stopper

Manufactured in polypropylene.

Alternative  to the traditional stopper system  for plugging the ends of the irrigation tube, making the plugging/unplugging operation quicker and easier. 

Assembly: insert the tube into one of the opening, bend the end of the tube over and insert it into the other opening. 

Application in standard pe32 tube.

Dripper stopper 5x3mm

Manufactured in polypropylene.

Assembly:  insert the tapered part of the accessory into the tube.

Application: 
- measure 7 x 5: plug the holes made with the  3 mm punch, used to locate the drippers,,micro-sprinklers, micro-diffusers  and  threaded diffuser into the tube pe32 (maximum permitted thickness 2 mm.). Is also used as stopper for the microtube 6 x 4.

- measure 15 x 10: plug the holes made with the  7 mm punch,. Used to locate the outlets  (ref. 1051, 1103, 1104, 1141) on pe32 tube (maximum permitted thickness 4,8 mm.).

- measure 5 x 3: plug the 1 and  2 mm diameter holes in pe32 tube (maximum permitted thickness 2 mm).

Tape double joint valve

CHARACTERISTICS: minimum load loss,
withstands up to 5 bar without any appreciable
water loss both when open or closed in normal
conditions.
MATERIAL/S: manufactured in reinforced
polypropylene. O ring seal in NBR.
APPLICATION: accessory used to connect
standard PE low pressure tubes for microirrigation
branch lines.
ASSEMBLY: introduce the tape until tip in the
conical end of the valve and turn left the screw
until fitting it. Do not damage the shape of
the tape.

Double joint pipe connectors valve

CHARACTERISTICS: minimum load loss, withstands up to 5 bar without any appreciable water loss both when open or closed in normal conditions.
MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR. .
APPLICATION: accessory used to connect standard PE low pressure tubes for microirrigation branch lines.
ASSEMBLY: this type of accessory is inserted inside the tube

M.97 valve and sleeve

CHARACTERISTICS: minimum pressure loss, withstands up to 5 bar without any appreciable water loss when open or closed in normal conditions.
MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR.
APPLICATION: accessory used to connect standard PE low pressure tubes for microirrigation branch lines.
ASSEMBLY: this type of accessory is inserted inside the tube.

M.97 valve and threaded sleeve

CHARACTERISTICS: minimum pressure loss, withstands up to 5 bar without any appreciable water loss when open or closed in normal conditions.
MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR.
APPLICATION: accessory used to connect standard PE low pressure tubes for microirrigation branch lines.
ASSEMBLY: this type of accessory is inserted inside the tube.

Tape-pipe connectors valve

CHARACTERISTICS: minimum pressure loss, withstands up to 5 bar without any appreciable water loss when open or closed in normal conditions.

MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR.

APPLICATION: for 16-17 mm tape and 0.1 to 0.9 mm sprinklers.

ASSEMBLY: introduce the tape until tip in the conical end of the valve and turn left the screw until fitting it. Do not damage the shape of the tape.

Safety valve

CHARACTERISTICS: minimum load loss, withstands up to 5 bar without any appreciable water loss both when open or closed in normal conditions.
MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR. Ring in acetal resin.
APPLICATION: accessory used to connect standard PE low pressure tubes for microirrigation branch lines.
ASSEMBLY: this type of accessory is inserted inside the tube.

Thread-tape valve

CHARACTERISTICS: minimum load loss, withstands up to 5 bar without any appreciable water loss both when open or closed in normal conditions.
MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR.
APPLICATION: for 16-17 mm tape and 0.1 to 0.9 mm sprinklers.
ASSEMBLY: introduce the tape until tip in the conical end of the valve and turn left the screw until fitting it. Do not damage the shape of the tape.
STANDARDS: gas thread conforming to standards UNE 19009, ISO R7, UNI 338 and DIN 2999.

Tape-tape valve

CHARACTERISTICS: minimum pressure loss, withstands up to 5 bar without any appreciable water loss when open or closed in normal conditions.
MATERIAL/S: manufactured in reinforced polypropylene. O ring seal in NBR.
APPLICATION: for 16-17 mm tape and 0.1 to 0.9 mm sprinklers.
ASSEMBLY: introduce the tape until tip in the conical end of the valve and turn left the screw until fitting it. Do not damage the shape of the tape.

Attachment for tubes with spike

MATERIAL/S: body in reinforced polypropylene, head in POM.
APPLICATION: used to fasten the tube to the ground. The length of the spike may be increased by adding more simple spikes part number 1125 and fastening them together.