Articles 1 - 12 total of 13
New patented system (mod. 200002026/7) thanks to the incorporation of improved technology achieved by our experience, research and development. Rosca BSP. CHARACTERISTICS: • System without joint adapter socket. • Clamp design with arms, avoiding the traditional split clamp system, which has allowed us to improve the fit of the clamp on the tube. We obtain better fastening with less force. • Asymmetrical saw-tooth pattern on the clamp. • Clamp and tube cannot rotate during tightening. • To avoid losing it, the clamp cannot fall off even if the nut is fully undone. The O ring seal is also immobilised by the clamp. • The nut contains a stop. During assembly, the operator feels that the optimum installation position has been reached, which prevents any over-tightening. • Fitting PN 16. • For use in low, medium and high density polyethylene tubes. • Designed to conform to UNE standards relating to mechanical unions for polyethylene tubes. MATERIALS: • Body: polypropylene. • Clamp: acetal resin. • Nut: reinforced polypropylene. • O ring seal: NBR. ASSEMBLY: 1. Loosen the nut to the maximum without needing to take it off completely. 2. IMPORTANT: do not remove the clamp from its seating. 3. Insert the tube, ensuring that it passes over the O ring seal and reaches the grooves inside the part. 4. Tighten the nut up to the end of travel stop. RECOMMENDATIONS: • Cut the tube off square. • Remove any imperfections from the outer edge of the part of the tube to be inserted into the fitting. • Ensure that the tube is clean so that the O ring seal fits perfectly to the contour. • Do not allow the tube to adopt a stressed position.

Male thread connection

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

Female thread connection

INFO FITTING


Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

Coupling

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

 

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

Reduced coupling

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

90º elbow

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

90º male thread elbow

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

90º female thread elbow

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

Symmetrical tee joint

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

Female thread tee joint

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.

Reduced centre tee joint

INFO FITTING

Materials:
- central body in polypropylene.
- nuts in ppfv (glass fiber reinforced polypropylene).
- o rings seal: nbr
- teeth socket in pom (poliacetal).

Use in standards tubes p.e.b.d and p.e.a.d conform to the une 53131.

For the threads it is advisable to use ptfe tape .

Pn= 16 bar at 20ºc

Conforming to standards une en 714, en 911,  en 712 and en 713.